You scrub the shower, but it still looks grimy. Often the culprit isn’t the tile. It’s the grout, the thin lines between tiles that soak up soap scum, minerals and mildew over time.
The good news is that you can usually bring grout back to life without hiring anyone. This beginner-friendly guide walks you through cleaning, small repairs and sealing, so your shower looks fresh before holiday guests arrive.
Why grout gets dirty
Most common grout is cement-based and porous, which means it absorbs water and whatever is in it. In a busy shower, that adds up quickly. Sealing helps, but sealers wear off over time, especially in wet areas.
What you’ll need
- A stiff grout brush or an old toothbrush
- Baking soda and water
- A spray bottle
- An oxygen-based cleaner (optional, for tougher stains)
- Rubber gloves and eye protection
- A grout saw or utility tool (for repairs)
- Premixed or bagged grout that matches your color
- A rubber grout float and a damp sponge
- Grout sealer and a small applicator brush
Step 1: Start with a gentle clean
Mix baking soda and water into a thick paste. Spread it along the grout lines and let it sit for about 10 minutes. Then spray lightly with warm water and scrub with your brush in short strokes along the line. Rinse well.
For many showers, this alone makes a visible difference.
Step 2: Tackle stubborn stains
If stains remain, try an oxygen-based cleaner mixed according to the package directions. Apply, wait the recommended time, scrub and rinse.
A few important safety notes:
- Never mix cleaning products, especially bleach with ammonia or acids. The combination can create dangerous fumes.
- Turn on the fan or open a window while you work.
- Avoid harsh acidic cleaners on natural stone tile, which can etch the surface. Check what your tile is made of first.
Step 3: Inspect for damage
Once the grout is clean and dry, look closely. Small hairline cracks, crumbling spots or gaps let water get behind the tile, which can lead to bigger problems. Note any areas that need repair.
If you see loose tiles, soft spots in the wall or signs of water damage, stop and call a pro. Those are signs of a deeper issue that new grout won’t fix.
Step 4: Repair small damaged sections
For small areas:
- Use a grout saw to carefully scrape out the damaged grout, going about halfway down the joint. Work slowly so you don’t chip the tile edges.
- Vacuum or brush out the dust.
- Mix or open your replacement grout according to the package directions.
- Press grout into the joint with a rubber float held at an angle, working diagonally across the tile.
- After it firms up slightly (check the package for timing), wipe the tile surface with a damp, well-wrung sponge.
- Let it cure for the full time listed on the package before using the shower.
Color matching can be tricky, so test a small hidden spot first if you can.
Step 5: Seal the grout
Sealing helps grout resist water and stains. Once your grout is clean, dry and fully cured, apply a penetrating grout sealer with a small brush or applicator bottle, following the product’s directions. Wipe any sealer off the tile surface before it dries. Most sealers need several hours or more before the area gets wet again.
Step 6: Keep it clean longer
A few small habits make a big difference:
- Squeegee the walls after each shower.
- Run the bathroom fan during showers and for a while after.
- Do a quick weekly scrub of grout lines.
- Reseal according to your sealer’s recommendations, often once a year in busy showers.
Don’t forget the caulk
Grout belongs between tiles. The corners and the joint where the wall meets the tub or shower pan should usually be flexible caulk, not grout. If that line is cracked or moldy, it’s worth replacing, too.
The wrap-up
Fresh grout can make a whole bathroom look newer, and it helps protect your walls from water. With a brush, a little patience and a weekend afternoon, you can get your shower looking guest-ready without a full renovation.
Image: Modern bathroom, house interior via Rawpixel, CC0 1.0