A frozen pipe is one of the most stressful winter surprises a homeowner can face. When water freezes, it expands, and that pressure can crack a pipe and cause leaks or water damage once things thaw.

The good news is that insulating exposed pipes is one of the easiest and cheapest winter DIY jobs. With a few foam sleeves and some tape, you can protect the most vulnerable pipes in an afternoon. Here’s how.

Which pipes need insulation

Focus on pipes in unheated or poorly heated areas, where temperatures can drop close to freezing. Common trouble spots include:

  • Garages
  • Crawl spaces
  • Unfinished basements
  • Attics
  • Pipes along exterior walls
  • Pipes under kitchen or bathroom sinks on outside walls

Hot water pipes are worth insulating too. It helps water stay warmer as it travels and can reduce wasted energy.

What you’ll need

  • Foam pipe insulation sleeves (pre-slit tubes) sized to your pipes
  • Measuring tape
  • A utility knife or sharp scissors
  • Duct tape or the tape recommended by the insulation maker
  • Zip ties (optional)
  • Fiberglass pipe wrap for spots near heat sources, if needed
  • Work gloves and a flashlight

Measure the outside diameter of your pipes before shopping. Common household sizes are 1/2 inch and 3/4 inch, and the sleeve packaging will tell you which pipe size it fits.

Step 1: Inspect and clean the pipes

Check each pipe for leaks, drips or corrosion. If you find an active leak, fix it or call a plumber before insulating. Wipe off dust and dirt so the tape sticks well.

Step 2: Measure and cut the sleeves

Measure each straight run of pipe and cut the foam sleeve to length with a utility knife. It’s fine to use several shorter pieces for a long run. Just make sure the ends meet snugly.

Step 3: Fit the sleeves over the pipes

Open the slit along the side of the sleeve and press it around the pipe. Many sleeves have a self-sealing adhesive strip. Peel off the backing and press the edges together firmly. If yours don’t, close the seam with tape every foot or so.

Step 4: Handle corners and joints

Elbows and T-joints are where gaps often happen. For a 90-degree corner, cut the ends of two sleeves at a 45-degree angle so they meet neatly. For T-joints, cut a notch in the main sleeve so the branch sleeve fits into it. Tape every joint so no pipe is exposed.

Step 5: Seal the gaps

Wrap tape around all seams and where sleeves meet. Small gaps can let cold air reach the pipe, which defeats the purpose. Zip ties can help hold sleeves in place on vertical runs.

Step 6: Keep foam away from heat sources

Standard foam insulation shouldn’t touch very hot surfaces, such as the flue pipe on a water heater or furnace. Keep foam a safe distance away, and follow the manufacturer’s directions. Fiberglass wrap rated for higher temperatures may be a better choice near heat sources.

Extra freeze-protection tips

  • Seal drafts near pipes, like gaps around dryer vents or where pipes pass through walls.
  • On very cold nights, open cabinet doors under sinks on exterior walls so warm air can reach the pipes.
  • Let a faucet drip slightly during extreme cold, which can help prevent freezing.
  • Know where your main water shut-off valve is, and make sure everyone in the house does too.
  • Keep the thermostat at a steady temperature, even when you’re away.

When to call a professional

If pipes are hard to reach, already frozen, or in an area with signs of water damage or mold, call a licensed plumber. Never use an open flame to thaw a frozen pipe. In very cold climates, a plumber can also discuss heat cables designed for pipes.

Wrap-up

Insulating exposed pipes is a small, inexpensive project that can save you from a major headache. Identify the pipes in cold areas, fit snug foam sleeves, seal every joint and add a few simple habits on frigid nights. Your pipes and your wallet will both make it through winter in much better shape.

Image: Copper Pipe Burner Parts by Sea Dreams Wood Boat Forum via Flickr, CC0 1.0